UPCOM 4E1 to 4-port Ethernet converter is an Ethernet extension device that use PDH, SDH or other microwaves to carry Ethernet data, allowing users to transfer Ethernet data into E1 frame format through the existing TDM (E1) links and then re-convert E1 back to Ethernet data at the remote terminal.
HPC-4E1-4ETH, 4E1 to 4 Ethernet converter support GFP-F, VC (Virtual Concatenation), LCAS (Link Capacity Adjustment Scheme) and professional GUI (Graphical User Interface) NMS (Network Management System).
HPC-4E1-4ETH is an IP over TDM converter, which supports the conversion from MAC frames to 1–4 E1 lines. The maximum bit rate is 8 Mbps (4E1 lines). it can meet various requirements and can be customized to meet your network needs. It not only provides alarms and status of the E1 line and Ethernet interface together with advanced management functions, such as throughput statistic of the Ethernet, but also supports the Unification Network Management via SNMP and GUI. It conforms to international standards and can be used with third-party device that follow the same protocol.
4-port 100M Ethernet interfaces operate in full-duplex or half duplex with flow control, the mode can be set or monitored by management software. The device also has multi-port bridging capability to handle up to 5 bridge ports. The Bridge supports two modes of operation: VLAN-Enable and VLAN-Disable modes. In VLAN-Enable mode, it creates sub-groups of bridge ports within the bridge. Each sub-group is associated with a unique VLAN ID (VID). Frames containing a VID can only be forwarded between bridge ports which are members of the specific VLAN, enabling a total separation between different VLAN users within the same bridge; In VLAN-Disable mode, the bridge forward frames ignoring the VID.
E1 interface ports
● Supports automatic removal and recovery of E1 channels that used for carrying payload.
● Supports the embedded E1 BER Tester function, to detect any E1 channel of 4 channels.
● Jitter tolerance and jitter transfer characteristic compliant to ITU-T G.823.
● The differential delay between any two of the 4 E1 can be up to 220ms
Ethernet Interface Ports
● Provides up to 4 shared Ethernet interfaces.
● 1024 MAC address table and 5-minute aging time.
● Accepts frames with length between 64 and 1916 bytes (otherwise filtering).
● VLAN setting function based on tags compliant to IEE 802.1Q.
● Throughout statistic of the Ethernet packets based on port, such as error packets.
● Configurable pause flow control.
● Optional optical Ethernet interface compliant to IEEE 802.3u 100BASE-FX standard and electrical Ethernet interface compliant to IEEE 802.3u 100 BASE-TX standard.
● 4 Ethernet ports are 10/100 BaseT Based, but fiber optical FX type ports are also possible with ranges up to 120 km.
GUI Management Interfaces
● GUI via serial RS232 port and telnet.
● 4E1-4ETH network management platform based on SNMP.
ĐẶC TRƯNG
- Support GFP-F encapsulation recommendation G.7041;
- Support Virtual concatenation(VCAT) and Link Capacity Adjustment Scheme (LCAS) recommendation G.7042;
- Support Ethernet to n*E1 mapping recommendation G.7043;
- Support Ethernet to single E1 mapping recommendation G.8040;
- Bandwidth is increased without damaging the Ethernet data;
- E1s in the local and remote sides can be arranged arbitrarily, such as: the remote E1 port 1 can communicate with local E1 port;
- Supports bandwidth unbalanced usage – when some E1s cannot work properly (i.e. the bandwidth of the sending and receiving can be 2E1 and 3E1 respectively);
- Provides the E1 connection-ship between local and remote system (accessed via GUI);
- E1 tributary signal loopback automatic detect and cut off; when some E1 signal is detected as looped back, it will be not employed for carrying payload temporarily, and when the loopback is broken, this E1 will resume to be used;
- Remote/local E1 loopback function will be convenient for E1 line (transmission system included) testing;
- Complete alarm which is selectable to be shown between local and remote. Historical & Current alarm databases;
- Single-board design with small dimension, 1U high and low power consumption;
- Support DC48V and AC 220V power supply;
- Support 0-50°C wide operating temperature range;
- Warranty:3years
THÔNG SỐ KỸ THUẬT
| E1 interface | |
| Bit rate | 2.048Mb/s±50ppm |
| Code format: | HDB3 |
| Line Impedance | 75 Ohm BNC and 120 Ohm RJ45 |
| Standard | Jitter transfer, Jitter tolerance comply with ITU-T G.703、G.704、G.823 recommendations |
| Ethernet Interface | |
| Connector | RJ-45 |
| Working mode | Auto-negotiation |
| Standard | Complies with IEEE 802.3 and 10/100 Base-Tx Ethernet Protocol |
| Ethernet related parameters | |
| MAC address table capacity | 1024 |
| MAC aging time | 5 min |
| Minimum frame-length | 64 bytes |
| Maximum frame-length | 1916 bytes |
| Working mode | Support auto-negotiation compliant to IEEE802.3u |
| VLAN function | Disabled as default, you can set VLAN’s from GUI |
| Flow control | Enabled as default |
| Bandwidth | ≈n×E1（n=0～4）Default is 4×E1 ≈8Mbps |
| Physical | |
| Dimension | 434mm*44mm*155mm（width*height*depth） |
| Weight | 5kg |
| Power consumption | 8W |
| Power supply | DC 48V or AC96 -260V or DC&AC dual power |
| Operating temperature | -5-65oC |
| Storage temperature | -40-70oC |
| Humidity | 5%~95% (non-condensing) |
Products in the same series
| Model | Description |
| HPC-4E1-4ETH | 4E1(75ohm&120ohm) + 4*10/100BASE-Tx , GUI manager,AC96-260,DC48V |
| HPC-8E1-4ETH | 8E1(75ohm&120ohm) + 4*10/100BASE-Tx, GUI manager,AC96-260,DC48V |
| HPC-16E1-4ETH | 16E1(75ohm or 120ohm) + 4*10/100BASE-Tx, GUI manager,AC96-260,DC48V |
| HPC-4E1-3ETH/Fx | 4E1(75ohm&120ohm) + 3*10/100BASE-Tx+1*100M Fx, GUI manager,AC96-260,DC48V |
| HPC-8E1-3ETH/Fx | 8E1(75ohm&120ohm) + 3*10/100BASE-Tx+1*100M Fx, GUI manager,AC96-260,DC48V |
| HPC-16E1-3ETH/Fx | 16E1(75ohm&120ohm) + 3*10/100BASE-Tx+1*100M Fx, GUI manager,AC96-260,DC48V |
Download
Tham khảo thêm các sản phẩm khác của Công ty TNHH Công Nghệ và Viễn Thông Hải Phong chúng tôi
Thêm một bình luận
Sản phẩm tương tự
SDH/MSTP nhỏ gọn
Model: SDH-8E1-4ETH
- 19” rack mountable, 1U height compact size
- System supports point-to-point, chain and ring network applications
- Gigabit Ethernet to STM-1 conversion, data rate up to 63 x VC12
- STM1 / STM-4 and n x E1 co-working simultaneously as network uplinks
- System supports 2 x STM-1, or 2 x STM-4 optical ports as ring protection
- Ethernet supports 4 x GE electrical ports or 3 x GE electrical ports plus 1 x GE optical port
- Order-wire channel for point-to-point and point-to-multipoint voice communication
- Sophisticate configurable system protection with SNCP network protection and 1+1 interface protection
- In-band management channel for remote control and system management
- Two expansion slots for E1 or various data or voice modules
- Alarm relay is provided for external alarm facility connection
- Remote firmware and software upgrade is available
- Redundancy power supply is supported with any combination of the power supply unit
Bộ ghép kênh quang PDH 16E1+ 4ETH được quản lý
Model: HPOM-16E1-4ETH
- Provides 16*E1 +4-port 100M Ethernnet over the fiber;
- Support 1-port Fiber or 1+1 Fiber back up;
- Provide 4*100 Mbit/s Ethernet channels, Ethernet speed can be set for each port on based on any multiples of n*32 Kbit/s;
- Provides one RS232 channel for option;
- Provide one hotline channel for option (order wire);
- Speed of optical port is 155Mbps, transmission range can reach 20, 40, 60, 80,100,120Km;
- E1 interface code is HDB3; E1 vibration characteristic conforms to ITU-T G.703、G.823 and G.742;
- Ethernet port supports full/half duplex, 10M/100M auto-adaptable, throughput is full duplex 100 Mbit/s;
- Ethernet port supports dot1Q VLAN setting possibility and port based VLAN;
- Layer2 intelligent switch possibilities for 4*Ethernet ports;
- Ethernet packet size supports 1916 byte and 4 Ethernet port could be set separately, jumbo frames are supported;
- Simultaneous 16E1 & 100 Mbit/s full duplex operation;
- LED indicators for alarm function and can monitor remote device status;
- Support DIP switch management;
- Supports E1 local and remote loopback for installation;
- Broadcast Storm Protection, Port monitoring;
- Current alarm and alarm history database;
- GUI based RS232 NMS manager for easy and convenient monitoring and management;
- Support DC48V and AC 220V power supply;
- Support -5-65°C wide operating temperature range;
- Warranty:3years
Bộ ghép kênh quang 8E1+ 4ETH PDH được quản lý
Model: HPOM-8E1-4ETH
- Provides 8*E1 +4-port 100M Ethernnet over the fiber;
- Support 1-port Fiber or 1+1 Fiber back up;
- Provide 4*100 Mbit/s Ethernet channels, Ethernet speed can be set for each port on based on any multiples of n*32 Kbit/s;
- Provides one RS232 channel for option;
- Provide one hotline channel for option (order wire);
- Speed of optical port is 155Mbps, transmission range can reach 20, 40, 60, 80,100,120Km;
- E1 interface code is HDB3; E1 vibration characteristic conforms to ITU-T G.703、G.823 and G.742;
- Ethernet port supports full/half duplex, 10M/100M auto-adaptable, throughput is full duplex 100 Mbit/s;
- Ethernet port supports dot1Q VLAN setting possibility and port based VLAN;
- Layer2 intelligent switch possibilities for 4*Ethernet ports;
- Ethernet packet size supports 1916 byte and 4 Ethernet port could be set separately, jumbo frames are supported;
- Simultaneous 8 E1 & 100 Mbit/s full duplex operation;
- LED indicators for alarm function and can monitor remote device status;
- Support DIP switch management;
- Supports E1 local and remote loopback for installation;
- Broadcast Storm Protection, Port monitoring;
- Current alarm and alarm history database;
- GUI based RS232 NMS manager for easy and convenient monitoring and management;
- Support DC48V and AC 220V power supply;
- Support -5-65°C wide operating temperature range;
- Warranty:3years
Bộ ghép kênh quang 4E1+ 4ETH PDH được quản lý
Model: HPOM-4E1-4ETH
- Provides 4 *E1 G.703 transparent transmission over the fiber;
- Support 1-port Fiber or 1+1 Fiber back up;
- Provide 4*100 Mbit/s Ethernet channels, Ethernet speed can be set for each port on based on any multiples of n*32 Kbit/s;
- Provides one RS232 channel for option;
- Provide one hotline channel for option (order wire);
- Speed of optical port is 155Mbps, transmission range can reach 20, 40, 60, 80,100,120Km;
- E1 interface code is HDB3; E1 vibration characteristic conforms to ITU-T G.703、G.823 and G.742;
- Ethernet port supports full/half duplex, 10M/100M auto-adaptable, throughput is full duplex 100 Mbit/s;
- Ethernet port supports dot1Q VLAN setting possibility and port based VLAN;
- Layer2 intelligent switch possibilities for 4*Ethernet ports;
- Ethernet packet size supports 1916 byte and 4 Ethernet port could be set separately, jumbo frames are supported;
- Simultaneous 4 E1 & 100 Mbit/s full duplex operation;
- LED indicators for alarm function and can monitor remote device status;
- Support DIP switch management;
- Supports E1 local and remote loopback for installation;
- Broadcast Storm Protection, Port monitoring;
- Current alarm and alarm history database;
- GUI based RS232 NMS manager for easy and convenient monitoring and management;
- Support DC48V and AC 220V power supply;
- Support -5-65°C wide operating temperature range;
- Warranty:3years
Bộ chuyển đổi Ethernet 16E1 sang 4 với Quản lý VLAN và GUI
Model: HPC-16E1-4ETH
- Support GFP-F encapsulation recommendation G.7041;
- Support Virtual concatenation(VCAT) and Link Capacity Adjustment
- Scheme (LCAS) recommendation G.7042;
- Support Ethernet to n*E1 mapping recommendation G.7043;
- Support Ethernet to single E1 mapping recommendation G.8040;
- Bandwidth is increased without damaging the Ethernet data;
- E1s in the local and remote sides can be arranged arbitrarily, such as: the remote E1 port 1 can communicate with local E1 port;
- Supports bandwidth unbalanced usage – when some E1s cannot work properly (i.e. the bandwidth of the sending and receiving can be 2E1 and 3E1 respectively);
- Provides the E1 connection-ship between local and remote system (accessed via GUI);
- E1 tributary signal loopback automatic detect and cut off; when some E1 signal is detected as looped back, it will be not employed for carrying payload temporarily, and when the loopback is broken, this E1 will resume to be used;
- Remote/local E1 loopback function will be convenient for E1 line (transmission system included) testing;
- Complete alarm which is selectable to be shown between local and remote. Historical & Current alarm databases;
- Single-board design with small dimension, 1U high and low power consumption;
- Support DC48V and AC 220V power supply;
- Support 0-50°C wide operating temperature range;
- Warranty:3years
Bộ chuyển đổi Ethernet 8E1 sang 4 với Quản lý VLAN và GUI
Model: HPC-8E1-4ETH
- Support GFP-F encapsulation recommendation G.7041;
- Support Virtual concatenation(VCAT) and Link Capacity Adjustment
- Scheme (LCAS) recommendation G.7042;
- Support Ethernet to n*E1 mapping recommendation G.7043;
- Support Ethernet to single E1 mapping recommendation G.8040;
- Bandwidth is increased without damaging the Ethernet data;
- E1s in the local and remote sides can be arranged arbitrarily, such as: the remote E1 port 1 can communicate with local E1 port;
- Supports bandwidth unbalanced usage – when some E1s cannot work properly (i.e. the bandwidth of the sending and receiving can be 2E1 and 3E1 respectively);
- Provides the E1 connection-ship between local and remote system (accessed via GUI);
- E1 tributary signal loopback automatic detect and cut off; when some E1 signal is detected as looped back, it will be not employed for carrying payload temporarily, and when the loopback is broken, this E1 will resume to be used;
- Remote/local E1 loopback function will be convenient for E1 line (transmission system included) testing;
- Complete alarm which is selectable to be shown between local and remote. Historical & Current alarm databases;
- Single-board design with small dimension, 1U high and low power consumption;
- Support DC48V and AC 220V power supply;
- Support 0-50°C wide operating temperature range;
- Warranty:3years
0 đánh giá cho Bộ chuyển đổi Ethernet 4E1 sang 4 với Quản lý VLAN và GUI